适用于SamScene3D出品的v1.0.5版本ZYHB机场。
根据JEPPESEN的ZYHB航图制作（航图编号10-9B，生效时间2025年5月30日）。
一、请注意：
1、这与现实不完全相同，仅用于MSFS。
2、每次只能安装一个ZYHB的GSX配置文件，如需要安装该GSX配置文件，请先删除其他已有文件。
3、SamScene3D出品的ZYHB机场地景中部分滑行道编号与JEPPESEN航图中的编号不一致，因此，部分停机位置后推到设定滑行道时，请以JEPPESEN航图为准。
4、SamScene3D出品的ZYHB机场地景中部分部分停机位置并没有制作出来，它们包括：parking415-433，parking532，parking601-606，606L，606R，607，607L，607R，608，608L，608R，609-611。因此GSX中并没有为这些停机位置配置功能。

二、GSX配置文件特点：
1、所有停机位置均配置了后推线路（请参考航图，部分停机位原地开车后直接滑出，因此这些停机位置没有在GSX中定义后推功能）。包括以下停机位置：
（1）T1：gate2-10
（2）T2：gate19-21，gate30-48
（3）parking301-305，parking307-355，parking402-407，parking499-545，parkingY01-Y04
2、以下停机位置配置了VDGS：
（1）T1：gate02-10
（2）T2：gate19-21，gate30-48，parking499-507
3、以下停机位置配置了人工停机引导员：
parking301-305，parking307-355，parking402-407，parking415-433，parking508-531，parking533-545，parkingY01-Y04
4、以下停机位置在GSX中没有配置后推功能（原地开车后直接滑出）：
parking301-305，parking307-313，parking320-351，parking402-407，parking515-519，parking541-545
5、以下停机位置有自定义旅客登机行走路线：
gate2-10，gate19-21，gate30-48
6、所有停机位置的滑入路线均进行了修正，确保VDGS或人工停机引导员引导飞机前轮沿地面黄色线滑入。
7、清晰明了的后推方向描述，确保你不会推错方向。
8、对地面服务车辆摆放进行了位置自定义，确保不会出现车辆与建筑重叠的情况。

三、使用方法：
将zyhb-CFSO4590.ini文件复制到C:\Users\username\AppData\Roaming\virtuali\GSX\MSFS目录即可。

++++++_______++++++
Applicable to SamScene3D's ZYHB Airport version v1.0.5.
Produced based on the JEPPESEN ZYHB charts (Chart number 10-9B, effective May 30, 2025).

I. Please Note:
1.This is not identical to reality and is for MSFS use only.
2.Only one GSX configuration file for ZYHB can be installed at a time. If you wish to install this GSX configuration file, please delete any other existing files first.
3.Some taxiway designations in SamScene3D's ZYHB airport scenery do not match those in the JEPPESEN charts. Therefore, when setting pushback taxi routes from certain parking positions, please refer to the JEPPESEN charts as the authority.
4.Some parking positions are not modeled in SamScene3D's ZYHB airport scenery. These include: parking 415-433, parking 532, parking 601-606, 606L, 606R, 607, 607L, 607R, 608, 608L, 608R, 609-611. Consequently, GSX functionality has not been configured for these parking positions.

II. GSX Configuration File Features:
1.Pushback routes are configured for all parking positions (please refer to the charts; some parking positions allow for engine start followed by immediate taxi-out, so pushback is not defined in GSX for those). This includes the following parking positions:
(1) T1: gate 2-10
(2) T2: gate 19-21, gate 30-48
(3) parking 301-305, parking 307-355, parking 402-407, parking 499-545, parking Y01-Y04
2.VDGS is configured for the following parking positions:
(1) T1: gate 02-10
(2) T2: gate 19-21, gate 30-48, parking 499-507
3.Manual Marshalling is configured for the following parking positions:
parking 301-305, parking 307-355, parking 402-407, parking 415-433, parking 508-531, parking 533-545, parking Y01-Y04
4.Pushback is NOT configured in GSX for the following parking positions (engine start followed by immediate taxi-out):
parking 301-305, parking 307-313, parking 320-351, parking 402-407, parking 515-519, parking 541-545
5.Custom passenger boarding paths are configured for the following parking positions:
gate 2-10, gate 19-21, gate 30-48
6The taxi-in routes for all parking positions have been adjusted to ensure the VDGS or Marshaller guides the aircraft's nose wheel to follow the yellow ground line during taxi-in.
7Clear and unambiguous pushback direction descriptions to ensure you push back correctly.
8.Customized placement of ground service vehicles to prevent overlaps with buildings.

III. Installation Instructions:
Copy the zyhb-CFSO4590.ini file to C:\Users\username\AppData\Roaming\virtuali\GSX\MSFS.