Beschreibung
Twotter Revived v0.5.36
This exceptionally long development phase was driven by CCM's release of the Crazy Completionist Mod for GNS530/430 and the discovery of rich troves of reference materials, foremost data collected by NASA for N607NA, the DHC6-100 of Glenn Research Center's icing research.
de Havilland graciously provided a copy of the Maintenance Manu... JUST KIDDING ofc I found it somewhere on the Interwebs and de Havilland stays on the long list of companies and institutions that never responded to my attempts to contact them let alone offered help. Other reference materials used in creating this release: the FAA and EASA type certificates, Gas Turbine Combustion by Arthur H. Lefebvre, the PT6A training manuals and engine test procedures, Hartzell maintenance manuals, Wipaire float manuals, materials from Canada's NRC, the Garmin GNS 530 Pilot's Guide, the KI 525A and KT 76C pilot's guides, the KT 76C installation and maintenance manuals, Honeywell's EGPWS manuals and the FAA's TAWS standards, FAA NASR data for the radar sites, and a bunch more.
Thanks to CCM, first of all, for the GNS mod, and for the help getting the flight model on the book. <3 Thanks to Helloween and tredsell (both flightsim.to) for showing me how to make the passenger seating work.
If you installed the mod before, REMOVE all mod-related folders from your Community folder, especially old camera mods and the old propblur mod.
After installing, open the EFB's Config tab and pick your profile again, or check that the settings are what you want. The profiles changed and several options moved to new pages.
Twotter Revived
Twotter Revived is a free, community-built overhaul of the Aerosoft Twin Otter (MSFS 2020) for MSFS 2024. The goal is a faithful recreation of the aircraft, replacing stock sim systems with custom code where the sim falls short. Engines, electrics, radio navigation, and countless other systems are simulated in depth and interact with each other. The flight model has been redone and refined with invaluable help from CanadianCaptainMoustache.
Introduction
By now, this is probably what the modding community would call a "Total Conversion". Almost every system in the aircraft has changed, many have been replaced and redesigned, and even some core sim systems had to go in favor of custom implementations.
This is a test version. Please flag any issues you notice. I try to make sure the releases published on flightsim.to don't contain any blockers or stoppers that would keep you from flying, but bugs cannot be avoided, and if you find one, please return it to its rightful owner.
If you run into issues or have questions, contact me here or on Discord: aurel#3010 (if you're active on Discord, we most likely share a few flightsim servers). If you know about the aircraft IRL or aircraft development in MSFS, I'm especially grateful for your input and suggestions.
Installation
NOTE: Because of previous drama around Aerosoft mods, this mod is distributed as an archive containing xdelta files and an install script. You will need an original, unmodded installation of the Twin Otter 1.1.1 (installed using Aerosoft One, the legacy Aerosoft installer, or by other means) so the installation process can READ the original files and WRITE the changed files to the mod folder. Your original files will not be touched.
Until the install script has been executed, the mod will be inactive.
Before you report an installation error, please consider reinstalling a fresh copy of the Aerosoft Twin Otter in the last release version (1.1.1) and trying with that folder. If the errors persist, please contact me so we can figure out why they happen. The installer should now work with all popular versions of 1.1.1.
The contents of the zip file:
charliebravo-aircraftmod-twin-otter: this is all you need, you must unpack this to use the mod, the rest is optionalcompanion_mods/charliebravo-soundmod-twin-otter-turbineduke: this is an optional sound mod, you must own the Black Square Turbine Duke to use itcompanion_mods/charliebravo-y-cameras-twin-otter-*: these are optional mods that change the cockpit camera views, only one of them can be active at a time.historic_ndb_userpoints.csv: this file can be imported into Little Navmap to show historic (decommissioned) NDB beaconspresets/: this folder contains a set of presets for FSUIPC7 and possibly similar tools
You will still need to have the base model (i.e. the aerosoft-aircraft-twin-otter folder) in your Community/ folder for the mod to work.
Step by step:
- IMPORTANT: if you installed the mod before, REMOVE all mod-related folders from your Community folder, especially old camera mods and the old propblur mod (
z_aerosoft-twin-otter_propblur_mod) - UNPACK directly into Community or wherever you keep your Community add-ons
- OPEN the folder
charliebravo-aircraftmod-twin-otter - optionally, if you're paranoid or they are actually after you: EXAMINE install.bat and install.ps1, overwrite the xdelta executable with a version you trust
- DOUBLE-CLICK
install.bator RUNinstall.ps1in PowerShell (install.batis just a wrapper that executes the PowerShell script) - follow the prompts and SELECT your unmodified
aerosoft-aircraft-twin-otterfolder
In a perfect world, the changes to the mod folder are applied and you end up with a working mod and the lawyers have no leverage against me. I apologize for this, I can assure you that it has been even less fun to set this up. I contacted Aerosoft and Microsoft to get their blessing, but, so far, I didn't receive a response. It appears our Twotter is in some legal limbo: Aerosoft sold the rights to Microsoft, and now neither party appears to have any interest in the legacy product. xdelta helps me to stay on the safe side.
Liveries
In the mod folder, there's a tool fix-twotter-livery. Use it to fix any livery so it works in MSFS 2024 and shows up as a livery instead of a variant.
The Turbine Duke sound mod
This version includes an optional sound mod that re-uses the Black Square Turbine Duke soundbank with kind permission from Black Square and Boris Audio Works.
This sound mod only works for owners of the Black Square Turbine Duke. To enable the sound mod, copy it from companion_mods (do not copy companion_mods itself!) to your Community/ folder and launch install.bat in the charliebravo-soundmod-twin-otter-turbineduke folder.
If you experience any sound issues in the Turbine Duke while this mod is installed (and they go away if you disable the mod), please contact me. We don't want to bother the nice people of Just Flight with problems created by the Twotter.
Sound mod installation step by step:
- COPY the folder
charliebravo-soundmod-twin-otter-turbinedukefrom thecompanion_modsfolder in the archive to your Community folder - OPEN the copied folder
charliebravo-soundmod-twin-otter-turbineduke - DOUBLE-CLICK
install.bator RUNinstall.ps1in PowerShell - follow the prompts and SELECT your
bksq-aircraft-turbinedukefolder (usually, it is auto-detected)
Resources
- Project page on flightsim.to
- Discussion thread on the official MSFS forums
- Previews, release candidates, WASM source on Google Drive
- Twotter Revived manual
Aircraft manuals
- Microsoft DHC-6 Twin Otter
- Checklists (PDF)
- Introduction flight (PDF)
- Aerosoft DHC-6 Twin Otter
Product Manual MSFS (PDF)
- Product Manual FSX (PDF)
Thanks
- CanadianCaptainMoustache — for continuous input, advice, testing, the flight model, his GNS 530/430 mod (the Crazy Completionist Mod), which is ported into our GNS, and the prop blur mod our prop discs grew out of.
- JoseColme — for sharing his experience flying the type.
- Bagolu — for the wheel-chock visual model, and for fitting the ground power unit to the aircraft.
- Helloween and tredsell (flightsim.to) — for figuring out how to make pax work.
- hobanagerik — for tireless support and encouragement, better lights and cameras.
- Black Square and Boris Audio Works — for their kind permission to use the Turbine Duke soundbank.
- MaxHype — for finding the cause of the random WASM crashes in MSFS 2024, and for sharing the fix.
Changes to Aerosoft Twin Otter 1.1.1
- EFB "Twin Otter" app
- Config system
- Interactive and automatic checklists
- Persistence system
- New flight model
- One of the most advanced PT6A-27 models in non-professional flight simming
- Propellers: working autofeather, beta and reverse, new prop discs
- Custom or improved avionics (GNS 530/430 with CCM's Crazy Completionist Mod, KAP 140, KR 87, KT 76C, EGPWS)
- Gyros and compass system
- Custom radio navaids incl. a historic NDB database with one of the most advanced signal propagation models in non-professional flight simming
- Overhauled and updated fuel system, electrical system, hydraulic system, brakes
- Custom ice protection code (in preparation for custom icing)
- Cabin climate
- Custom wear & tear system (WIP)
- Walkaround: clickable doors, control surfaces and propellers you can move by hand, wheel chocks, GPU cart
- Pilot and co-pilot avatars, passengers in the cabin
- Reworked cockpit and exterior lighting
- Countless improvements to the cockpit
- Countless bug fixes
License & credits
The base aircraft is not redistributed by this project: the mod ships as binary deltas applied against your own copy of the Aerosoft Twin Otter 1.1.1 (see Installation). The original add-on remains the property of Aerosoft or Microsoft, I don't even know. The mod includes modified versions of sim assets which are used under Microsoft's Game Content Usage Rules (https://www.xbox.com/developers/rules) or their respective licenses (like Working Title's limited MIT license). This is a non-commercial fan project, not affiliated with, endorsed by, supported by, or even acknowledged by Microsoft, Asobo, or Aerosoft.
Source
I cannot distribute the complete project source because there are still leftovers of the base model in cfg and xml files, and this is exactly what killed the first Twotter mod by CCM. What I can distribute is the heart of the mod: the code the WASM module is built from. Apart from the bundled components listed below, it's in the public domain and you're more than welcome to take it apart, use and redistribute it. You can find it where the preview versions are (see Resources).
Bundled components
- Flap actuator audio (
fbw_flap_actuator.wav) — from FlyByWire Simulationsa32nx-wwise, licensed CC BY-NC-SA 4.0 (Attribution / NonCommercial / ShareAlike). - Ground power unit model (
CB_GPU) — "GPU (Aiport Ground Power Unit)" by omri_ha_muglob, licensed CC BY 4.0 (Attribution). Fitted to the Twin Otter by Bagolu. - Longley-Rice / ITM propagation core — the Irregular Terrain Model, created by the U.S. Department of Commerce NTIA/ITS, obtained via libradio by Saso Kiselkov. The files we ship carry no copyright notice or license block of their own; what we redistribute of Saso's work is his thread-safety modification inside them, and CDDL-1.0 is listed as the license for those parts of libradio. We assert no license of our own over any of it. Details:
CBDHC6/third_party/THIRD_PARTY_NOTICES.md. - DEFLATE inflate (
puff) — Mark Adler / zlib, zlib-style permissive license. - Laboured breathing audio (
cb_breathing_loop.wav) — cut from "male breathing long.wav" by boziav, licensed CC BY-NC 4.0 (Attribution / NonCommercial). - GNS 530/430 — Working Title's GNS 530/430, modified, under Working Title's "Modified MIT" license. It includes our port of CCM's Crazy Completionist Mod, shipped with his permission.
- Fonts — Roboto by Google, licensed Apache-2.0, and DSEG14 Classic by keshikan, licensed SIL Open Font License 1.1 (Reserved Font Name "DSEG").
- xdelta3 (
xdelta3.exe, used by the install script) — by Joshua MacDonald, version 3.1.0, licensed Apache-2.0. - Livery tool (
fix-twotter-livery.exe) — built withgo-webview2(MIT, its loader ISC),golang.org/x/sys(BSD-3-Clause),rardecode(BSD-2-Clause) and the Go standard library (BSD-3-Clause), with Roboto (Apache-2.0) embedded.
Data providers — thank you
- Terrain elevation based on ETOPO 2022 (NOAA NCEI).
- Coastlines, water bodies and ice from Natural Earth (naturalearthdata.com), and the GNS basemap (roads, railroads, rivers, borders, place names).
- Land cover from ESA WorldCover 2021 v200 — © ESA WorldCover project 2021 / Contains modified Copernicus Sentinel data (2021) processed by ESA WorldCover consortium, CC BY 4.0.
- Climate zones from the Köppen-Geiger maps by Beck et al. (2018) (Present and future Köppen-Geiger climate classification maps at 1-km resolution, Scientific Data), CC BY 4.0.
- Some navaid service ranges based on FlightGear (originally the X-Plane navdata compiled by Robin A. Peel).
- Historic NDB database based on OurAirports, FlightGear and older X-Plane navdata (Robin A. Peel), and KonBriefing's historic radio beacon lists.
- Radar sites checked against FAA NASR data.
Twotter Revived is a community project. It is not endorsed or certified by De Havilland Aircraft of Canada. It is not approved by anyone in any way, shape, or form for training or any other real-world application. Any real-world references are provided for entertainment and educational simulation use only and may be incomplete, outdated, configuration-specific, or inaccurate.
Häufig gestellte Fragen
Twotter Revived
A complete realism overhaul of the Aerosoft Twin Otter with dozens of custom systems including arguably the most advanced PT6A-27 simulation you can get for free.
Nutzerbewertungen
33 Bewertungen
Versionsgeschichte
# Patch notes v2024.3.260 -> v0.5.36 This exceptionally long development phase was driven by CCM's release of the Crazy Completionist Mod for GNS530/430 and the discovery of rich troves of reference materials, foremost data collected by NASA for N607NA, the DHC6-100 of Glenn Research Center's icing research. de Havilland graciously provided a copy of the Maintenance Manu... JUST KIDDING ofc I found it somewhere on the Interwebs and de Havilland stays on the long list of companies and institutions that never responded to my attempts to contact them let alone offered help. Other reference materials used in creating this release: the FAA and EASA type certificates, Gas Turbine Combustion by Arthur H. Lefebvre, the PT6A training manuals and engine test procedures, Hartzell maintenance manuals, Wipaire float manuals, materials from Canada's NRC, the Garmin GNS 530 Pilot's Guide, the KI 525A and KT 76C pilot's guides, the KT 76C installation and maintenance manuals, Honeywell's EGPWS manuals and the FAA's TAWS standards, FAA NASR data for the radar sites, and a bunch more. Thanks to CCM, first of all, for the GNS mod, and for the help getting the flight model on the book. <3 Thanks to Helloween and tredsell (both flightsim.to) for showing me how to make the passenger seating work. After installing, open the EFB's Config tab and pick your profile again, or check that the settings are what you want. The profiles changed and several options moved to new pages. ## Walkaround - All doors and baggage compartments have clickable handles on the outside. - With the control lock removed, the ailerons, elevator and rudder can be grabbed and moved by hand. - Dragging a secured propeller by hand releases its (invisible) securing straps. - Clicking a main tire places or removes the wheel chocks. - On the land variants, the rear fuselage, the airstair and the GPU cart have collision boxes. - Walking into the open left crew door or up the airstair puts you in the pilot's seat. - An unlatched crew door swings with the aircraft in taxi turns and under braking, and in the wind (works in flight, too). ## Crew & passengers (new) Thanks to Helloween (flightsim.to) and tredsell (flightsim.to) for doing the research and ground work! - Added the MSFS 2024 pilot and co-pilot avatars, with the co-pilot visible in the cockpit. - Passenger variants show passengers in the cabin. ## Compass system & gyros (new) - Added a flux valve that slaves the captain's HSI. Once aligned it slaves at 3° per minute, and fast after power-up or when you switch from FREE back to SLAVE. It swings in turns and when you accelerate. - Both directional gyros drift. The slaved HSI corrects its own drift, but the copilot's DG has to be reset with its knob from time to time. - The EFB Instruments tab has a Slaving Control with a slave meter, a SLAVE/FREE latch, and CW/CCW buttons that turn the HSI card in FREE mode. It replaces the Sync Gyros button. - The knob on the captain's KI 227 no longer turns the HSI card. With the unslaved KI 227 selected as ADF indicator, it turns the ADF card. - With "Gyros take time to spin up" switched on in the EFB Config tab, the directional gyros take about 4½ minutes to clear their HDG flag and coast for about 10 minutes after the power goes off. The attitude indicators are about three times faster and coast for 3 minutes. Cold-soaked gyros spin up more slowly. With the option off, the flags clear a few seconds after power-on. - With "Gyros take time to spin up" switched on, the gyros run on AC from the inverters, and the inverters sag with the DC bus. A weak or cold battery can slow the gyros down and bring up their flags. - The HSI HDG flag and the attitude indicator OFF flags depend on the gyro's power and rotor speed. The HDG flag no longer shows just because the avionics master is off. - The attitude indicators erect along a spiral instead of a straight line. ## KT 76C transponder (new) The stock KT 76C gauge had a whole range of issues, so I replaced it with our own fork. - In ALT mode the transponder reports the pressure altitude from the captain's encoding altimeter. Before, it used the copilot's altimeter with its baro setting, so turning the FO's baro knob changed the altitude ATC saw. - After power-up the unit takes 45 seconds to warm up. Until then it stays in standby and the reply light stays dark. - A new code goes out 3.5 seconds after you enter the fourth digit, or right away when you press IDENT. - The VFR code is 1200 everywhere. The stock gauge used 7000 outside North America and Australia. - The VFR code can be programmed, and the unit remembers the previous code. In SBY, set the code, press IDT, then VFR within 3 seconds. Holding VFR for 2 seconds recalls the previous code. Both codes are saved. (On the real unit, you press VFR while holding IDENT.) - In TST mode, 0 dims the display, 7 brightens it and 4 resets it. - Fixed CLR setting the code to 0000. - The IDENT buttons on the unit and on the left yoke both start a full 18-second ident. - The reply light (R) flashes when a ground radar or nearby TCAS traffic interrogates you. It is almost solid near busy terminal areas and dark in the bush. Terminal radars sweep about every 5 seconds out to 60 NM, en-route radars every 10 to 12 seconds out to 200 NM, and both are blocked by terrain and the radio horizon. - The radar sites are placed by a simple rule (airports with an approach or departure frequency), checked against the FAA's NASR data. My own research overrides the rule in 82 regions, and 54 of them have no radar at all (for example Greenland, many Pacific islands and parts of Africa). - Black Market: an optional radar detector on the EFB Config tab's Equipment page (off by default). In SBY, the R light and a soft ping tell you when you are being interrogated, and the unit still doesn't reply. ## GNS 530/430 CCM's Crazy Completionist Mod has been ported into our GNS 530/430. Thanks to CCM for his outstanding work breathing life into these units! <3 The items from his work are marked (CCM). The Twotter implementation is an almost feature-complete port of https://hangaraddons.com/addons/msfs-2024/panels/ccms-garmin-gns530430-crazy-completionist-mod-d38e621d (versions 1.0.0 and 1.1.0, plus the fixes from 2.0.1). Not ported so far: searching by name or city, the self-test overlay, and a few smaller items. - Added the AUX pages for trip and fuel planning, the scheduler, crossfill, flight timers, trip statistics, RAIM prediction, sunrise/sunset, and the CDI and alarm settings. Trip and fuel planning start with your present position and the destination, and update live. (CCM) - Without a fuel computer (the "Fuel and Air Data Computer" option on the EFB Equipment page), fuel planning starts blank until you enter fuel on board and fuel flow. - Fixed the Density Alt / TAS / Winds page being about 300 ft and 9 kt off. - Added the flight plan catalog on FPL page 2, with 19 stored flight plans that can be created, edited, copied, inverted, activated and deleted. (CCM) - Added Nearest pages for ARTCC, Flight Service, airspace and user waypoints, with a page menu. ENT tunes the selected frequency into the standby COM. Nearest airports, VORs, NDBs and user waypoints are searched out to 200 nm. (CCM) - Added the map pointer on the moving map, with bearing and distance to the pointer, and Measure Dist? in the page menu. (CCM) - Added user waypoints (up to 1000), created from the WPT pages, Direct-To or the map pointer. (CCM) - Added a vector basemap to the NAV maps, with roads, railroads, rivers, lakes, cities, state and province lines, and the names of states, countries, seas and lakes. (CCM, map data from Natural Earth) - Added the VSR and FLOW data fields, the wind vector, more Map Setup options, and the Pilot's Guide map ranges from 500 ft to 2000 nm. (CCM) - Added the TERRAIN alerts: the TERRAIN annunciator, the TERRAIN ALERT pop-up and a marker where your flight path meets the terrain. They are driven by the aircraft's TAWS, which also does the talking. (CCM) - On the Terrain page, CLR hides the airspace and runways. - Traffic switches to standby on the ground and to operate once you're airborne. (CCM) - With the traffic advisory system removed on the EFB Equipment page, the GNS has no Traffic page, no traffic on the maps and no traffic warnings. The change takes effect at the next aircraft load. - Fixed the traffic warning window opening on one unit while the other shows the Traffic page, and a second traffic advisory leaving the bezel keys dead. - Added a Checklists page (AUX, Utility), loaded with the Twin Otter's checklists for the variant's gear type. You can edit the lists, and the EFB Config tab can restore the original ones. (CCM) - Holding the COM flip-flop key for 1.2 seconds makes 121.500 active, holding CLR for 1.2 seconds opens the default NAV page. (CCM) - Each unit remembers its last position and satellite data, so a normal start takes 12 to 45 seconds. If the aircraft moved more than 54 nm, the unit needs about 2.5 minutes to find itself, and after six months without use it searches the sky for about 5 minutes. The EFB's GPS acquisition option shortens these long searches to about a minute (Quick, the default) or keeps the real unit's times (Normal, set by the Recommended and Realistic profiles). Runway and in-air starts have a fix right away. (inspired by CCM) - With the coupled VNAV option off, advisory VNAV picks its target waypoint and altitude like the real unit and remembers the target you pick. (CCM) - Each unit keeps its own units, date/time format and VNAV settings. - The display colors match the Garmin PC trainer, and NEXRAD uses the Pilot's Guide colors. (CCM) - The WPT pages open on the active waypoint, Select Next FPL Apt? steps through the airports in the flight plan, and ENT on a VOR's frequency tunes it. (CCM) - Fixed the arrival page showing the arrivals of the departure airport. - Fixed the arrival page loading the wrong arrival after changing the transition or runway, and the FPL page losing track of the active leg while you edit the plan. ENT on the selected approach moves on to the transition. (CCM) - Fixed fast typing in waypoint fields being overwritten by an older search. - Fixed the 430's OBS key putting the 530 and the captain's HSI into OBS mode. - Fixed the "Set course to" prompt showing up when the HSI course pointer slews by itself. - Fixed the coupled VNAV option sometimes being ignored. Changes to it take effect at the next aircraft load. - The VOR/LOC info box shows the station's ident and distance only while the station is received. ## Flight model & handling - Re-tuned drag, cruise speed and stall speeds against the POH. Max cruise at 10,000 ft is about 181 KTAS (the book says 182), and the stall speeds are within 2 to 3 kt of the book. - Re-tuned the lift, drag and pitch change of the flaps at every flap setting. - Reworked pitch stability, pitch damping and elevator authority. The elevator has its full certified travel (25° up, 16° down). - Re-tuned the fin, the rudder and single-engine handling. With one engine feathered, the rudder trim can hold the aircraft straight down to about 80 KIAS. - Rudder trim is neutral in cruise. The take-off setting is about 14 %, where the T.O. mark on the rudder trim indicator is. - VMO is 166 KIAS on the -300 with wheels or tundra tires (skydiver included) and 156 KIAS on all others (was 170). - Added the flap-elevator trim interconnect. A tab on the right elevator moves with the flaps and takes care of most of the pitch change, without turning the cockpit trim wheel. It can be switched off on the EFB Config tab, but I don't recommend it. - The exterior elevator tabs move separately: the left one with the trim wheel, the right one with the flaps. - The elevator and rudder trim wheels turn four times from stop to stop. The elevator trim indicator shows the trim wheel only, the interconnect doesn't move it. - While the autopilot is engaged, the trim wheel follows the autopilot and your trim inputs are ignored. - Fixed the aileron trim tab moving the wrong way. The aileron trim switch's glass cover rocks, but the rocker inside it stays still, this is an issue with Aerosoft's visual model. - Re-tuned the gear, contact points and tire heights. The main gear stiffens as it compresses, so the tires look the same at any weight. Re-tuned nosewheel steering friction. - The Climb, Cruise, Approach and Final situations start trimmed, with flaps, power and props set for the variant. Runway starts come with take-off flaps and rudder trim set. - Fixed floats and amphibians creeping forward when starting on the water. - Fixed the aircraft taxiing too fast during the runway start cinematic. - Floats and the amphibian don't offer the fuel truck, GPU, pushback or marshaller any more. ## Engines - Torque was rescaled to the PT6A-27 torquemeter constant (30.57 ft-lb/PSI) and depends on OAT. - Torque at altitude at the ITT limit, torque gained by reducing propeller speed, and the power cost of bleed air and the intake deflectors all match the POH charts. Added inlet ram. - Added the exhaust thrust, about 5 % on top of the propeller's. - Reshaped the fuel control's schedule, so the power lever no longer has a long dead band above idle. - Added a reverse propeller governor and torque limiter. In reverse, propeller speed stays a little below the selected rpm, and torque is limited to 50 PSI (about 42 PSI on the -100). - Fixed autostart (Ctrl+E), which hot-started both engines, and autoshutdown (Ctrl+Shift+E). Both run the copilot's start and shutdown sequences. - Fixed the engines running for several minutes after the tanks ran dry. ## Propellers - Autofeather works. Until now it only lit the ARM light. It arms with the switch on, both torques above 20 PSI and both power levers above about 86 % Ng. If an engine's torque drops below 12 PSI for 2 seconds, its propeller feathers and the other one is locked out. Retarding the power levers (rejected take-off) cancels it. - The propeller of a failed engine windmills until it is feathered, by you or by the autofeather. A propeller left unfeathered at shutdown drifts into feather about four minutes after it stops. - Added the power lever interlock. With both propeller levers below 91 % NP (about 2000 rpm), the power levers stop at idle and cannot be pulled into beta or reverse. The EFB Status tab tells you when the interlock is holding. - Below idle, the power lever sets blade angle directly, from 11° at idle to −15° at full reverse. The idle blade angle is 11° in flight and on the ground (was 3° and −7°). - The Beta Range lights come on when the blades go below 9°. The Beta Backup Disarmed caution light comes on with either power lever below idle or either propeller below 9°. The lights and the beta back-up system are on the right DC bus. - The -300 governs at up to 96 % NP (2112 rpm), per the POH. It was 2200 rpm. The -100 stays at 2200 rpm. - Feathering takes about 10 seconds at ground idle and about 3 seconds at full propeller speed. Going from idle to full reverse takes about 2 seconds. - Thrust comes from the sim's modern propeller model, with blade angles measured at the 30-inch station and feather at 87°. - The RESET PROPS light comes on when a power lever is pulled back below the 75 % Ng position while its propeller lever is below 90 %. ## Autopilot - KAP 140: The P (pitch) annunciator blinks when the autopilot can't take over the pitch axis, for example when you engage it far out of trim. - KAP 140: Altitude capture, ALT hold and the altitude alerter use the KAP 140's own BARO setting. Changing the BARO in ALT hold keeps the aircraft level. - KAP 140: Corrected the tooltips on the altitude arm button and the altitude selector knobs. - Re-tuned the pitch servo for better pitch tracking. - Fixed the aircraft sinking below the glideslope or glidepath at low approach speeds, and FLC failing to hold speed in steep idle descents with flaps. - Fixed false Trim in Motion alerts. The "check pitch trim" callout plays when the autopilot has held the trim at its stop for a while. - Fixed servo warnings during the KAP 140's power-on self-test. - Fixed the altitude alerter repeating its tone and callouts near the alert thresholds, and phantom alerts on avionics power-up. ## Terrain awareness (EGPWS / TAWS) - The TAWS has one voice, the one formerly called Custom. I dropped the Aerosoft and FlyByWire sets and the voice selector, as they drifted too far from the project's requirements. All callouts follow the TAWS volume setting. - The EGPWS computer runs on the avionics bus and stays silent with the avionics master off. - Fixed altitude callouts going off when the avionics are switched on below decision height. - The EFB Config tab has a TAWS page with the installation options ("program pins"): the TAWS class (A, B, or by role), which altitude callouts are fitted, the 500 ft callout, and what the cockpit GPWS INHIBIT switch inhibits. Whether an EGPWS is fitted at all is set on the Equipment page. - The 500 ft callout can be Smart (silent on an ILS), Hard (every approach) or Above Field (500 ft above the nearest runway). - The GPWS INHIB button doubles as the caution and warning light, with one flash pattern for cautions and a faster one for warnings. It can be switched off on the TAWS page. - The EFB Instruments tab has a row of EGPWS buttons: FLAP OVERRIDE, STEEP APPROACH, G/S CANCEL, TERRAIN INHIBIT, CALLOUTS OFF, AUDIO INHIBIT and MODE 6 LOW VOLUME. All of them except MODE 6 LOW VOLUME reset at touchdown. - MODE 6 LOW VOLUME halves the volume of the altitude callouts, MINIMUMS and BANK ANGLE. - With no TAWS fitted, the EFB hides the TAWS tab and the EGPWS buttons on the Instruments tab. - The TAWS tab shows which inhibits are active. - Added the whoop-whoop to PULL UP, and SINK RATE is called twice. - Added 300 ft and 400 ft callouts. APPROACHING MINIMUMS is called at DH + 80 ft (was DH + 100 ft). - Altitude callouts are called once per approach and no longer repeat over rolling terrain. - BANK ANGLE is called at the limit, again 20 % further, and continuously beyond that. - Fewer nuisance alerts on low go-arounds and in the circuit. A go-around started below 150 ft counts as a departure, so TOO LOW FLAPS and the premature descent alert stay quiet while you clean up. The departure phase ends at 1500 ft, or when you turn back toward the runway. - DON'T SINK only arms after a take-off or a low go-around. - TOO LOW FLAPS is called below 150 ft (was 170 ft). - Warnings repeat at a steady pace in a continuing descent. After a PULL UP, TERRAIN keeps sounding while the terrain is still closing. - The look-ahead terrain alert uses the standard clearance for each phase of flight. It stays quiet on a normal final, and short gusts no longer set it off. - The premature descent alert and the Above Field 500 ft callout use land runways of 2000 ft or longer, grass included. ## Instruments & radios - The TORQUE PRESS needles lag behind the engine like the real hydraulic gauges, more so with cold oil. If you find that annoying, set Torque needle response to Quick on the EFB Config tab. - The turn coordinator ball is a custom inclinometer. - HSI and CDI deflection match the GNS scale in every phase of flight. - Fixed the HSI glideslope needle staying parked on hand-flown GPS approaches. - The first officer's altimeter has its own baro setting. It used to use the autopilot's. - Fixed the altimeters' baro correction, which was off by about 50 ft at pressure settings far from 29.92. - The altimeter needles and drums follow the baro knob as it turns. - Fixed the baro knobs spinning a full turn backwards at some settings. - The KAP 140, KR 87 and KT 76C displays dim with the light in the cockpit, and all three use the same LCD color. - Fixed the HSI heading bug knob not turning left through input events. - The chronometer's DME display has a decimal. - DME: Fixed the DME losing the station when you fly over it. Overhead, it shows your height above the station. - Fixed the per-runway localizer width always falling back to a default. - The historic NDB database has ICAO regions and the missing station elevations. ## Lighting - The pilot's panel lighting knob lights the whole instrument panel, both sides, including the engine instruments. All three panel lighting knobs have 27 steps, and the top end is less bright. - The copilot's panel lighting knob dims the GNS 530/430 bezels. - The console lighting knob dims the KAP 140, KR 87 and KT 76C bezels and the audio panel. They stay lit with the avionics master off. - Added the missing lights on the captain's HSI, altimeter and turn coordinator, and on the copilot's HSI. - Added a Volumetric light shafts option for the landing and taxi lights to the EFB Config tab's Lighting page (off by default). - Each landing light has a wide, dim flood around its main beam, representing scattered light. - The landing and taxi lights are aimed per variant. - The taxi light throws a wide, short pool of light that starts at the nosewheel. - The landing and taxi lights show their lens flare and appear in reflections. - Added a "Strobe flashes in cloud" option to the EFB Config tab's Lighting page (on in the Recommended and Realistic profiles). The strobes, beacon and navigation lights light up cloud and haze around the aircraft. - The wingtip strobes point 30° toward the nose, so they light the cloud ahead. - Re-tuned the strobe, beacon and navigation lights. ## Cockpit & systems - Hydraulics: Reworked the pump and valve logic to follow the POH's description. The pump runs until both accumulators are full, and a check valve keeps enough pressure in the brake accumulator for two or three brake applications. - Fuel: Corrected the usable capacity of the main and wing tanks (forward 181, aft 197, 44 per wing tank, all US gal). - Electrical: Fixed the DC loadmeter showing zero while charging, and showing a discharge with the generators online (a workaround for an SU7 bug). Battery temperature follows charge and discharge. - Electrical: Improved the avionics master switch handling. Switching between external power and battery no longer reboots the GNS units. - Crew oxygen: The EFB Climate tab shows the crew's blood oxygen. Without oxygen it drops with altitude, to about 91 % at 10,000 ft and 85 % at 14,300 ft. Below 85 % you hear laboured breathing, and the copilot calls for oxygen when it's needed. There are no other consequences. - Cabin climate: Fixed the cabin failing to hold its temperature in cruise with RAM AIR partly open. - Persistence: Warm engine, cabin and battery temperatures are only restored if you start within 100 nm of where you left the aircraft. - Cockpit: Fixed momentary push-buttons not releasing through input events, and sped up the condition lever's animation to match its snap action. ## Checklists - The copilot sets take-off elevator trim for the aircraft's CG, and take-off rudder trim to about 14 %. - Power lever items accept 0–5 % as idle. - For the battery recharge and run-up checks, the copilot waits for Ng to settle at idle before advancing the power levers by 15 % Ng. - "Power Levers 85% NG, pause 5 s" checks Ng only. It completes when both engines are held at 75–90 % Ng for 4 s, or at once when both are above 90 %. - The copilot sets the captain's altimeter, the first officer's altimeter and the KAP 140's BARO, each separately. - The "Compass and Gyros" check and the electrical test's gyro check require the HSI HDG flag to be clear. The hydraulic check reads accumulator pressure. - "Aircraft SECURE" secures the propellers as well as placing the chocks. - Fixed the copilot not turning off the Bleed Air switches. ## EFB app - Config tab: Added the Equipment, Lighting and Hardware pages. The Equipment page holds the airframe's optional installations: battery pack, ADF indicator, field-installed avionics master, EGPWS, Fuel and Air Data Computer, traffic advisory system, crew oxygen, flight director, and a radar detector from the Black Market. - Config tab: Settings with a few choices use buttons instead of sliders. - Config tab: The profiles also set the equipment, TAWS and lighting options. They no longer change the Hardware page. - Config tab: Shows the mod's version. - Payload tab: The passenger and cargo loaders keep the CG near the middle of the POH envelope at the loaded weight. - Payload tab: Every variant starts with the crew and some ballast in the aft cabin (150 lb, more where the CG needs it). - Payload tab: The SLA battery's extra weight no longer counts as payload. - Payload tab: The cabin plan shows the wing tanks and wing pump state. - Payload tab: Fixed boarding passengers resetting the co-pilot's weight, a refresh lockup, and the fuel tank steppers rounding incorrectly. - Status tab: Added a Propellers section (speed, blade angle, thrust and a Governor row) and an ESHP estimate in the TurbSim table. Peak torque statistics are in gauge PSI. - Status tab: The Gauges page shows what the HSI, the compass and the NAV 2 indicator display, and in Instructional mode the true values. - Instruments tab: Holds the DME, the Slaving Control and the EGPWS buttons. The altimetry rows moved to the Status tab. - Systems tab: The hydraulic pressure gauge is gone, and the Hand Pump button moved into the Cockpit group. On the cargo variants, the cabin door is labelled Cargo Door. - Ice tab: Replaced the ambiguous CLEAR with NO ICING. - Fixed the Esc menu confusing the EFB about the state of the flight. - Fixed the splash screen's buttons being pushed off-screen in landscape, and checklist auto-advance scrolling. ## Hardware, cameras, installation, misc - Liveries: Bundled fix-twotter-livery.exe, next to INSTALL.bat in charliebravo-aircraftmod-twin-otter. Drag a livery onto it (zip, rar, 7z or a folder) and it installs the livery as a livery of the mod's aircraft. That removes the livery's copy of Aerosoft's panel, which switched the mod's systems off for that livery. INSTALL.ps1 runs it after every update to register your installed liveries again. It needs WebView2 (part of Windows 11), and it refuses liveries for Microsoft's DHC-6 and liveries that change the 3D model. - FSUIPC: An FSUIPC7 / MobiFlight preset file for the custom cockpit controls ships in the presets folder of the zip. It covers the EFB-only controls, separate press and release presets, three-way switches, and axes for the dimmers and RAM AIR. - Hardware: Added options on the EFB Config tab's Hardware page for where the low end of your throttle axis goes (idle detent, zero thrust or full beta, zero thrust is the default), and whether the axis stops at the idle detent in flight (on by default). - Hardware: The reverse key bindings work on each power lever separately, and pressing reverse no longer throws the other lever into reverse. - Hardware: TOGGLE_FEATHER_SWITCHES and TOGGLE_FEATHER_SWITCH_1/_2 act as feather buttons. With the propeller lever on its aft stop, a press moves the lever through the gate to feather. Pushing the axis forward unfeathers the propeller. - Hardware: The elevator trim takes AXIS_ELEV_TRIM_SET and ELEV_TRIM_UP/DN. ELEVATOR_TRIM_SET is ignored. - Cameras: The stock Aerosoft views are part of the main mod. The flat views (by hobanagerik) and the custom views (based on Archer374's "Better Cameras") are optional companion packages in companion_mods, install at most one. Delete z_aerosoft-twin-otter_flat_cameras and any camera packages from the test releases. The installer checks for them and tells you. - Visuals: The prop blur discs are part of the main mod, uniform discs without the wagon wheel. Delete z_aerosoft-twin-otter_propblur_mod if it is still in your Community folder (the installer doesn't check for this one). - Fixed the installer failing on long Community folder paths and on stray desktop.ini files. - Sound: Restored propeller feathering audio with the Turbine Duke soundmod, and fixed the control lock playing the opposite sound. An EFB option turns off the Aerosoft gyro spool-down sound (switch it off if you use the Turbine Duke soundmod). - The tires are round.
Ähnliche Addons

Verkehrslandeplatz Cottbus/Neuhausen (EDAP)
Authentic representation of the Cottbus/Neuhausen airfield (ICAO: EDAP) as part of the "Lausitz Scenery" project. Custom buildings, high resolution DEM, static aircraft, and more included. Unfinished project with some known issues; provided "as is". Visit the detailed release notes for more information.
von aurel42

Lausitz Landmarks
This scenery project adds landmarks to the Lausitz area and Cottbus city in Microsoft Flight Simulator as part of the "Lausitz Scenery" project. Please note that the project is unfinished, with known modeling imperfections and potential performance issues. Featured landmarks include power station Jänschwalde and the Cottbus Altmarkt.
von aurel42

Verkehrslandeplatz Cottbus-Drewitz (EDCD, anno 2012)
Experience an authentic representation of Cottbus-Drewitz airfield around 2012 with this scenery project, part of the "Lausitz Scenery" project. Custom models for tower, terminal building, and aircraft shelters are included, along with high-resolution DEM and custom aerial data. Please note this project is unfinished and may have performance issues due to incomplete modeling.
von aurel42

ComancheProxy (A2A with Brunner CLS-E yokes)
ComancheProxy is a utility designed to bridge A2A Accu-Sim aircraft, such as the Comanche, with Brunner CLS-E force-feedback yokes via CLS2Sim by providing more accurate flight data than standard MSFS. It enables enhanced force-feedback effects by relaying expected control surface information. The tool also allows users to fly unsupported or encrypted aircraft in FSEconomy by modifying aircraft identification data. Configuration options support both yoke integration and FSEconomy profile compatibility.
von aurel42


Kommentar-Zusammenfassung
Die Rückmeldungen der Community zu Twotter Revived sind äußerst positiv. Viele Nutzer loben das Engagement des Entwicklers, die umfangreichen Verbesserungen sowie die Wiederbelebung der Aerosoft Twin Otter für MSFS2024. Besonders geschätzt werden das verbesserte EFB (Electronic Flight Bag), die aktualisierte Flugphysik, detaillierte Systeme und die Unterstützung eigener Lackierungen und Tablet-Funktionen. Wiederkehrende Problemfelder betreffen den Installationsprozess, die Kompatibilität mit bestimmten Versionen (die Mod funktioniert nur mit der Aerosoft-Version, nicht aber mit der Microsoft Twin Otter) und Schwierigkeiten mit Liveries, die meist mit Tools wie MSFSLayoutGenerator gelöst werden können. Gemeldete Bugs oder kleinere Probleme umfassen hydraulische Systemanomalien, VR-Cockpit-Darstellung, bestimmte Steuerungszuweisungen und gelegentliche Konflikte mit anderen Add-ons wie der Inibuilds L1011 oder der Hu-16 Albatross. In den Kommentaren finden sich hilfreiche Tipps zur Installation und zur Umwandlung von Liveries. Insgesamt wird die fortlaufende Entwicklung, der direkte Support und die intensive Kommunikation des Entwicklers sehr geschätzt, auch wenn derzeit zwingend die Aerosoft-Version der Twin Otter benötigt wird.
Zusammengefasst am 13. Nov. 2026
Melden Sie sich an, um an der Diskussion teilzunehmen
AnmeldenKommentare250
After flying this "revived" twin otter for a couple of weeks, I have to say I'm blown away. The level of detail put into each individual system is insane! Thank you so very much for bringing my fav plane back into the flight sim!!!
If I may have a suggestion, could you have a look at the smoke effect please? I did a bad startup (yeah, its been a long time since I flew her), and one enging started smoking a lot, making the sim verry laggy and my PC fans to speed up.... not great. So if you have time to have a look :) thank you in advance.
And THANK YOU Again for bringing back my Boy
Note that both the smoke and the "fire" are placeholders. If anyone knows how to make nice effects, please consider donating a set. :D
Also thank you for the quick reply, the second startup went well, so I lond as I do it well, it won't fry my PC hehe, but yeah, the effect was too much...
To give you an idea of my PC:
-R7 5700X
-RTX5070
-32GB RAM
edit: Okay, the next release will be much easier on the CPU during the ca. 15s of smoke that a hot start can create (just mentioning this so the AI summary doesn't misread this as a general performance problem). On my system, the smoke went from a cost of 30 fps to 2 fps. That's acceptable for a temporary effect.
Looking forward for the next Update! you Rock ! :)
The Microsoft Twin Otter in MSFS2024 is a different aircraft and does not benefit from this mod.
It's a long and sad story.
The FS2020 Twotter was the aircraft that converted me to MSFS back in the day, I owe it that. I was ready for MSFS2020 on launch day, messed around with it for a few days, but then abandoned it for XP11 again because it was so immature. Months + several MSFS updates later, I saw the release of the Twotter, and decided to give MSFS another shot with some Caribbean hops. Those first flights completely sucked me into the beauty of the MSFS world, so for that reason I simultaneously cherish this add-on while I also utterly despise how the Twotter was treated by the publisher.
Many thanks to Aurel42 for simultaneously making the Twin Otter not only flyable, but significantly better in FS2024.
My notes:
- I haven't done much in IFR with her yet, but I would not miss the stock flight director, if you could perhaps find a way to remove it. First of all, that style of ADI is clearly not compatible with a flight director. Second, it's persistent...if you have no power on the airplane, the FD will still function as a wing-leveler by default. This is one thing that has always bugged me with the AS Twin Otter. Is there any path to a) hide it until the AP modes are engaged or b) just remove it, for realism?
- Aliasing the BKSQ Turbine Duke sounds is a brilliant stroke. They are not really appropriate for a 3-blade prop/PT6A airplane, but the added character, especially with your beta range modification, is welcomed. The sounds were always a huge point of contention with this airplane when it was in Aerosoft's hands. I wonder what could be done in the future? I have a couple thoughts..I would be happy to chat on Discord. Handle: "youretootall"
The Flight Director is only enabled in the "Classic" profile. You can turn it off on the Config tab of the EFB.
The wing leveler issue is confirmed: I only cleared the modes, not the AP master upon power loss. Will be fixed in the next release.
If you can point me to an aircraft with a more appropriate engine/prop sound, I'd be happy to look into creating another sound mod. That's probably the best we can do until I win the lottery and we can send a professional sound guy to record a Twotter and build a new soundbank.
I'm just trying to do right by her. :D